Tramway Français Standard


The Tramway Français Standard is a type of tram designed and manufactured by Alstom for use on various tramway systems in France. The TFS is no longer in production, having been superseded by Alstom's Citadis range of tramcars.
Two different models of the TFS were produced, both being articulated designs. The first model, the TFS-1, was built for the opening of the Nantes tram system in 1985. As built, these were single-articulated 6-axle tramcars with a high floor and steep stepped access from low level boarding platforms. All the tramcars built in this form have since been rebuilt with an added low-floor centre section, thus becoming 8-axle double-articulated cars. Nantes subsequently bought additional TFS-1 trams in this 8-axle configuration.
For the opening of the Grenoble tram system, the TFS-2 variant was created. This was also a 6-axle tramcar, but had a different articulation mechanism with a very short central section carried on a four-wheel truck. This allowed a low floor to be carried through most of the length of the car and between the wheels of the central truck, although the sections over the outer bogies are still at a high level and accessed by three steps from the low-floor section. All the doors are within the low-floor section. The advantages of this layout ensured that all subsequent users of the TFS tramcar have adopted the TFS-2 variant.

TFS-2

Technical data

The tramcars are articulated vehicles and are long and 44.2 tonnes in weight. The cars cannot work as multiple units, although in case of an emergency two cars may be coupled using an emergency coupling system. With one tramcar not functioning, and braking diminished, speed is limited to.
The tramcars have the following characteristics:
Length
width
height
Gross weight44.2 tonnes
Power550 kW
Speed
Passenger capacity52/125

Car

The tramcar is built on a chassis wide joined by a central chassis on which is assembled a single pantograph. The car has 3 bogies, one on each ends and one below the central portion.
Only the central parts of the cars have a lowered floor, at high to enable access to disabled users by four doors. The parts at both ends of the tramcars are built at high accessible by a small three-step staircase.

Motors

The two outer bogies are each equipped with a 275 kW electric motor. This gives the TFS a high acceleration, allowing its use on lines with steep gradients and/or frequent stops, and a top speed of.

Operation

Like most modern trams, the TFS vehicles are one-person-operated. The driver is responsible for monitoring activity on board, including the operation of the doors. In most versions of the TFS, a single lever controls both acceleration and braking and contain an integrated dead man's switch. The versions used in Saint-Etienne, though, use pedals, consistent with the earlier PCC trams. The tramcars are equipped with land-train radios and ICS, infrared SAM and onboard pointwork control.

Fleet

Currently, TFS or TFS-derived trams are used on all lines of the tramway networks in Nantes, Grenoble, and Saint Etienne, as well as on Île-de-France tramway Line 1 operated by the RATP north of Paris. They had formerly operated on Île-de-France tramway Line 2 west of Paris and in Rouen until they were replaced by Alstom Citadis trams in 2002 and 2012, respectively. The TFS trams on Paris line 2 were moved to line 1, and the ex-Rouen trams were sent to Gaziantep, Turkey in 2013.
NetworkSchemeYear builtTypeNumber of carsCar numbers
Nantes11985TFS-120301-320
Nantes21988TFS-18321-328
Nantes31991-1992TFS-16329-334
Nantes41993-1994TFS-112335-346
Grenoble11987TFS-2202001-2020
Grenoble21989TFS-2152021-2035
Grenoble31991-1992TFS-232036-2038
Grenoble41995-1997TFS-2152039-2053
Rouen21994 TFS-2 28801-828
Saint-Étienne"Un désir nommé tramways", Jean-Paul RAHON - SIOTAS11991TFS-2 derivative15901-915
Saint-Étienne21998TFS-2 derivative20916-935
RATP11992TFS-2 17101-117
RATP21996-1997TFS-2 18118-119 & 201-216