Suzuki Alto


Suzuki Alto is a kei car built by Suzuki. Its selling points have long included a low price and good fuel economy. The model, currently in its eighth generation, was first introduced in 1979 and has been built in many countries worldwide. The Alto badge has often been used on different cars in Japan and in export markets, where it is considered a city car.

Nameplate history

In Japan, the Alto badge was originally meant to be for the commercial use version of the Fronte passenger car. When introduced, the Alto was only available as a two-door "light van" and with bare-bones equipment. However, Suzuki generally did not use the "Fronte" badge in export, usually calling all versions "Alto" abroad. Most early export Altos were thus technically speaking rebadged Suzuki Frontes. These were exported with changes such as enlarged engines, sometimes modified bodywork. Thus the Japanese [|SS40] Fronte became the SS80 Alto with a 796 cc engine abroad. The Alto badge gradually took over in Japan as well, as the distinction between kei commercial vehicles and passenger cars was diminished in early 1989. The Fronte line was retired in March 1989. The Alto plate has been used on export versions of various Indian-built derivatives since the early 1990s, as neither cars are restricted by the kei rules and Indian cars are also considerably cheaper than Japanese-built ones.
Thus, the European-market models were actually:
Since 2014, the Suzuki Celerio has replaced the Alto in Europe and other export markets. Alto was thus momentarily a JDM-only badge, but the Indian-built Maruti Alto is currently marketed as a Suzuki Alto in several countries.

First generation (1979)

The first generation, introduced in May 1979, is a three-door cargo version of the Fronte passenger car, equipped with a folding rear seat. Front suspension comprised coils struts, with leaf springs at the back. The steering was of the recirculating ball type, and four-wheel drums were used. On introduction, the Alto received the T5B two-stroke three-cylinder engine, producing at 5500 rpm. The Alto was a "micro sensation" when introduced, largely due to its rock bottom price of ¥470,000. This low price was made possible by a number of Japanese special concessions for commercial vehicles: most notably, the engine was subject to less stringent emissions rules and did not require expensive twin catalysts. Two fewer doors provided another saving, as did the exemption from commodity tax. The Alto's success changed the kei-car market, and other producers such as Subaru quickly followed suit with cut-price "commercial" vehicles that were really intended for private use.
Suzuki was unable to keep up with demand the first few years, particularly in the home market. The Alto helped Suzuki move into seventh place in Japanese production for cars and trucks. In the last full year of production for this generation, it was still by far the best selling Kei car, with the Alto outselling the Fronte at a rate of about five to two.
In May 1980 a fully automatic two-speed option was added to the Alto SS30. In January 1981, the F5A four-stroke from the Fronte was also made available for the Alto; although it only had a single-barrel carburettor, it too put out but at 6,000 rpm. Torque was considerably lower, however, down from. 1981 saw also the year that it became available in the United Kingdom, as Suzuki began selling cars there that year.
In export markets, the Alto name was used for the passenger car versions as well as on commercials, while the van was marketed as the "Suzuki Hatch" in Australia. The four-doors were not proper hatchbacks, only featuring an opening rear window. Export cars were also available with twelve-inch wheels, unlike the domestic versions which only used ten-inch units until the introduction of the 4WD version in October 1983. The 4WD "Snow Liner" thus gained an extra of ground clearance. Most export Altos were passenger car versions, and usually received the F8B engine and the SS80 chassis code. The 800 had better performance, and due to the higher possible gearing it saw an improved gas mileage as well - by about ten percent according to Suzuki. The SS80 was also built in New Zealand, by South Pacific Suzuki Assemblers at a rate of six per day. It was introduced in New Zealand in March 1980.
While Suzuki held on to the two-stroke engine concept for a half decade longer than any of its Japanese competitors, eventually market pressures and ever tightening emissions regulations spelled its end in the Alto by September 1981. The Jimny, however, did use the same engine as late as 1987.
By 1984, the 800 cc Alto/Fronte were introduced in Pakistan and were locally manufactured by Pak Suzuki Motors along with the 1000 cc Jimny.

Suzuki Hatch (Australia)

In Australia the SS40V was sold as the Suzuki Hatch, only available as a two-seat commercial vehicle. This meant it was taxed at 35 percent duty as opposed to 57.5 percent for passenger cars, and sales were not affected by Australia's then-quota on import cars. The Hatch originally offered a single-carburetted engine with at 6000 rpm and at 4000 rpm. The side rear windows were covered with fibreglass by default, with a glass panels optional. The only other option was air conditioning. The Hatch was by far the cheapest new car sold in Australia at the time, although equipment was limited: the buyer received standard vinyl seats and mats and cross ply tires, with the only concession to luxury being a push-button AM radio. M. W. Suzuki in Victoria, Suzuki's distributor for Southern Australia, introduced the "800 pack" in January 1981 that included the motor. The pack also added steel-belt radial tyres, 12-inch wheels, front-wheel disc brakes and bolder bumpers front and rear.

Second generation (1984)

The second generation was introduced in September 1984. This generation Alto echoed the design of the GM M-platform that underpinned the 1983 Suzuki Cultus. It continued with the F5A engine of the SS40, but also became available with turbocharged and multi-valve engines thereof, mainly in the "Works" series. In December 1984 a four-wheel-drive version was added; until it arrived Suzuki had kept the four-wheel-drive version of the first generation Alto on offer. Performance versions of the Alto family first appeared in September 1985 when a fuel injected and turbocharged engine with was made available; this could also be had in combination with four-wheel-drive. The Alto Turbo gradually acquired more performance-related modifications until the Alto Works version was introduced in February 1987. This was the first kei car to reach the legal limit of. It acquired considerable popularity, with models of it still made by Fujimi. A five-door body became available in October 1985. This was superficially identical to that of the Fronte's, but the rear seat folded flat and it was technically speaking a commercial vehicle. This was the first five-door commercial of its kind in Japan, and was originally a special model introduced to celebrate the one millionth Alto produced.
In July 1986 the CA/CC71 received a rather thorough facelift. New wraparound headlights, a new dash and interior heralded the new available ITL rear suspension, a three-link rigid setup. Some lower end models retained the earlier leaf sprung rigid axle; those with ITL received the CA/CC72 chassis code. A "Walkthrough Van" was introduced in January 1987, while at the other end of the spectrum, the personal coupé Cervo on the CA/CC72 base was introduced in 1988 with a new F5B engine. In August 1987, higher spec Altos became available with a three-speed automatic rather than the two-speed unit that had been used before.

Other markets

Most export markets received the passenger car version, which would have been badged "Suzuki Fronte" in Japan, but were usually sold as Altos abroad. When equipped with the 543 cc F5A engine, the export model code is SB305. Most cars sold outside of Japan, however, received the larger F8B engine and the SB308 model code.

Europe

The 796 cc, F8B-engined CA/CB91 was sold in Europe with either a four-speed manual or two-speed automatic transmission. Export Altos were technically speaking Frontes, as this was the name used for passenger versions in Japan. They received larger bumpers, making them longer and wider. European Altos received the same facelift as the CA/CB72 did in late 1986, followed by a market specific facelift in January 1988, unveiled at the Brussels Motor Show. This model remained in production for the European market until 1993, when it was replaced by an also Maruti-built 1-litre version of the Cervo Mode, which was sold as the Alto until 2002. The Maruti 800 did continue to be available under its own name in Europe until 2004, when it could no longer pass emissions and safety requirements.

Pakistan

While the car has been long retired in other markets, it remained in production in Pakistan under the moniker Suzuki Mehran. The Pakistani version is essentially a simplified basic rebadged second-generation Suzuki Alto CA/CB91 which was sold in the Japanese and European market from 1984-1988. The Mehran had been in production due to its cost effective nature and cheap parts availability. In March 2019, The moniker Mehran officially ended its production after 40 years of production.

China

Around 1990, the China Ordnance Industries Corporation purchased the complete rights and all machinery for manufacturing the SB308 Alto from Suzuki. COIC charged four hitherto military enterprises with manufacturing the Alto: Chongqing Chang'an, Jilin Jiangbei, Xiangtan Jiangnan, and Xi'an Qinchuan were all to switch over to civilian manufacture. Chongqing Chang'an were able to adapt Suzuki's Just-in-time manufacturing methods and were the first to market the car, in 1992. Jilin Jiangbei lost money on each car built and ended up on the brink of bankruptcy; Xiangtan Jiangnan never got production off the ground, while Xi'an Qinchuan suffered a fire and chose to develop their own design instead. Chang'an ended up without real competition in the segment. Chang'an's productivity set a new standard for the Chinese auto industry.
In 1993 Chang'an Motors took over production of the Alto. The Chang'an Suzuki SC7080 Alto was produced with the same F8B engine as used in other export markets, and was replaced by the facelifted SC7081 Alto/City Baby/Little Prince/Happy Prince in 2001. The top of the Line Happy Prince, discontinued in 2007, used the sportier looking front bumper, grille, and bonnet of the Alto Works. Citing lower sales and stating that upgrading the design to meet new regulations would not be cost effective, Chang'an ended production of the old Alto on 28 July 2008. A total of 504,861 were built by Chang'an Suzuki between 1993 and 2008.
Another version called JN Auto has been built by Jiangnan Auto. As of Dec, 2010 Zotye's Jiangnan Alto is one of the cheapest car in the world, with a price tag of $2830. The entry-level model comes with the F8B three-cylinder. An inline-four engine with a displacement of and an output of was also available. The Jiangnan TT was eventually replaced by the Zotye Z100.

Third generation (1988)

The third generation replaced the CA71 in September 1988. This was the last generation of Alto to have an associated Fronte model. It had strikingly angular styling, with an unusual glazed C-pillar on the 5-door. Another curiosity of this generation was the availability of a version with a sliding door on the driver's side, the "Slide Slim", intended to simplify entering and exiting in tight spaces. It also made egress easier for the old and the infirm. The Slide Slim has two regular doors on the passenger side. When the Fronte name was discontinued in October 1989, the passenger car versions became Altos. Initially the CL11 used the 12-valve F5B engine known from the SS71 Cervo, but with an added 6-valve version in lower-spec versions. A DOHC version was also available in the Twin Cam Rl. Passenger car versions had the same engines, but all with 2 PS less due to more stringent emissions controls. The fuel-injected, 12-valve, turbocharged Works models came with an SOHC engine or a DOHC version. The front-wheel-drive Works' were available with a 3-speed automatic in addition to the standard 5-speed manual.
This generation was generally not exported, and was never built by Suzuki with engines of more than 660 cc nor with left-hand-drive. It arrived late in export markets, only by 1993 after the earlier export version had been retired, and it was only seen in a very few places, namely New Zealand, Hong Kong, and Singapore. In most countries the earlier Alto/Fronte was replaced by an Alto-badged Maruti Zen. With a 0.8-liter engine the CL11 Alto was built with left-hand-drive in South Korea, Poland, Romania and Uzbekistan as the Daewoo Tico, and also in China by Anchi.

660cc era

When the Kei car standards were changed in 1990, the engine was upgraded to the , and the Alto became the CL/CM/CN/CP21 in the process. The new standards also allowed for a longer car, which meant new bigger front and rear bumper, and new headlights and grille. Lower grade Van versions received a 6-valve engine, while passenger car versions got a single-cam 12-valve version. This engine was upgraded to in January 1991. 4WD versions with the three-speed automatic transmission were fuel-injected and offered three more horsepower. The F6A-engined Works RS/X and RS/R still claimed the legally limited with of torque, but the lower grade i.e. Turbo received a 6-valve SOHC-engine producing and of torque. Reflecting decreased tax benefits for commercial Kei cars, the Works series were now classified as passenger vehicles, allowing for a real back seat. The lineup was reorganised in January 1991, with a lot of new engine specifications.
In September 1991, responding to increasing safety demands, the Alto received side impact protection. Also, the vertical door handles on three-door versions were replaced by traditional horizontal ones. The re-engineering was extensive enough to necessitate new model codes, with vans becoming CL/CM22 and passenger versions now called CR/CS22. While most of the engines remained as they were, the Alto Van's engines were updated with power output up to.
This was the model that reached limited exports. The New Zealand version was mostly the same as the Japanese market five-door van model, with a cargo-oriented bare-bones trim combined with the rather soft Japanese suspension settings and light, low-geared steering. Unlike the Japanese models, however, this low spec was coupled to the four-valve engine with and a standard five-speed transmission. A three-speed automatic was also available. In a period test, this model reached the 0–100 km/h benchmark in 15.9 seconds and a top speed of.
A very limited production version for competition purposes arrived in 1992, called the Alto Works R. This was a lightened, strict two-seater with four-wheel-drive, a close-ratio five-speed transmission, and a tuned engine - although official output remained, as required by the Kei regulations. The car has an adjusted ECU and a free-flow Suzuki Sport RHB31 turbocharger, as well as a different throttle body. Less than a hundred were built, although it continued to be available until the arrival of the next generation Alto. This model, without a backseat and with racing bucket seats in front, was classified as a van and accordingly received the CM22V chassis code, unlike the usual Alto Works. The undercoating and most creature comforts were deleted and the car sat on steel wheels, which made the car about lighter than a regular Works RS/R.

Alto Hustle

Suzuki also produced a version of the Alto, known as the Alto Hustle, with a raised roof behind the front seats. This was unusual in that it used a modification of the five-door Alto's body rather than a completely new body, allowing Suzuki to market it as part of the Alto family. Its appearance was similar to the Nissan AD Max van. The Hustle was short-lived, only being offered between November 1991 and October 1993.
The engine options were mostly as for other Altos, albeit without the turbocharged offerings. The standard model has, while a four-valve version has depending on if it was carburetted or fuel injected. The lowest and highest-powered versions were also available with four-wheel-drive, and there was a bare bones two-seater version on offer.

Fourth generation (1994)

The fourth generation appeared in November 1994. The design was marked by simplicity, as Suzuki strived to return to making a more basic car. The Slide Slim model, with its sliding door on one side, was discontinued, as were some of the higher end versions of the third generation Alto such as the Regina. The new Wagon R took over much of the more expensive Alto's market share, leaving the Alto to compete at the lower end of the market. The fourth generation was generally not exported, with most foreign markets instead receiving Alto-badged versions of the Indian-built Maruti Zen.
The F6A engines were joined by a new high-performance K6A for the Works RS/Z model. Front-wheel drive or full-time four-wheel drive were offered, in three- or five-door sedans or as a three-door van. The Works model was also reclassified as a sedan, as many advantages for light commercial cars had vanished. The tailgate and rear doors are still fairly angular, but the front was more rounded than previous models.
;Chronology
In March 1995, the Alto Sv model appeared. This was a special fuel economy model, well equipped with air conditioning, power steering, AM/FM cassette stereo, etc. The "Alto With", a limited sporty edition based on the well-equipped Sf model with a front and rear spoiler, appeared in June 1995. In July a version of the Works Turbo ie/s called the Limited appeared; this had special stereo equipment and keyless entry and power locks. It was developed by AddZest. In November 1995, the Works model received a new grille and front bumper, with a bigger opening. In May 1996, the l'Èpo model appeared, this three or five-door sedan was based on the Se/Le model and was also available with four-wheel drive. This version received full power equipment, remote key entry, distinctly upholstered full fabric seats, hubcaps and many other amenities.
The Works Turbo F Limited ie/s version appeared in November 1996, offering a carbon panel, special alloy wheels, and more spoilers. In April 1997, the range received a facelift with side door impact beams and a new front design, with new marker lights beneath the headlights and a redesigned trunklid. The Alto l'Èpo P2 appeared at the same time, using a fuel injected version of the 12-valve engine with rather than the usual carburetted unit. All 12-valve models fitted with four-wheel drive and automatic transmission received a fuel injected version, as was the case since the third generation Alto. The l'Èpo models also received a new airbag. The Works models only received smaller changes at this time, such as white-backed meters in the dashboard. The RS/Z also received 14-inch wheels and fuller equipment. In November 1997, the even better equipped l'Èpo Limited model appeared, with a more powerful stereo system including a CD player. In January 1998, the Works Sports Limited model appeared, a Works ie/s with 14-inch wheels and special seats. In May the "Alto Beam" special model appeared, with UV reflecting glass and extra large seats.
In March 1995, a second iteration of the Works R arrived, again a limited production vehicle with a close-ratio transmission, built for competition purposes. Like the first Works R it was built in less than one-hundred examples, but this one appeared in two series: The Series 2 had sold out by October 1995 and the third series was available from January until September 1998. Unlike the first Works R, this one was a passenger car version and received the new, lightweight K6A engine. It was lighter than the regular Works RS/R, and the engine was considerably more powerful - although claimed output remained as per the regulations, torque increased from 10.5 to 11.0 kgm. Period sources state that the engine's actual output was at least. The engine received considerable changes over the regular Works, many more than the first Works R. The throttle body and camshafts were different, while a larger HT06/RA12 turbocharger was fitted, along with 260 cc injectors and a larger intercooler. The weight savings were only over the Works RS/Z for this model. This was the end of the Works R series of cars, foreshadowing the end of the Works badge in 2000.

Fifth generation (1998)

The fifth-generation Alto was introduced in October 1998. The styling was generally more rounded, the shape of the cabin showing the Alto's relationship with the new Suzuki Kei. The 658 cc K6A engine was now also available without a turbocharger, joining the turbocharged version and the familiar 657 cc F6A engines. The turbocharged Works models were available with a 60 hp F6A engine or a 64 PS VVT K6A. The front-wheel-drive RS/Z was sold with a non-VVT K6A engine when in combination with a 4-speed automatic transmission, it too with a claimed 64 PS. In December 2000, the Works versions were discontinued, as the Alto was realigned as an economy version. The Suzuki Kei Sports picked up the Works' mantle.
Several derivatives were produced from this generation. Suzuki produced two "classic-style" versions: the Alto C with a deep chrome grille and a curious headlamp arrangement by which circular main lamps were joined with ovoid sidelights and indicators, which was shared with the Alto Works; and the Alto C2 which had separate headlamps and sidelights and a wider grille. Mazda also sold the standard Alto as the Carol, and Mitsuoka used the Carol as a basis for their Ray. Pakistani production began in 2000 utilizing the old carburetted F10A four-cylinder engine.
Beginning in mid-1999, and originally imported from Japan, the car was also sold in Colombia as the Chevrolet Alto. As the market for two-door cars was minimal in Colombia, it was only available with five doors. The Colombian model was equipped with a one-litre, sixteen-valve inline-four engine with at 6500 rpm, an engine it shared with the locally made Chevrolet Wagon R+. GM Colmotores began building it themselves in 2000 and kept it in production until 2003. The Chevrolet Alto was also exported to Ecuador.

Facelift

In December 2000, the fifth generation Alto received a thorough facelift, becoming the HA23. As the Works was discontinued, naturally aspirated versions of the K6A became the only ones on offer, with either or in an especially efficient lean-burn iteration. Front- or four-wheel-drive, manual and automatic transmissions were available, in either a 3- or 5-door hatchback body. A 3-door van version remained available.

Sixth generation (2004)

The sixth generation was introduced in 2004. The bonnet and headlamps curved down at the front, giving a similar effect to the Toyota WiLL Vi or the Citroën C2. The Alto was realigned as a less costly car to accommodate new models such as the Cervo and Alto Lapin. The more powerful engines were moved into the other more upmarket versions like the Suzuki Kei Works and Alto Lapin SS, leaving the Alto with only a version. In Japan, this version of the Alto was rebadged as the Nissan Pino and Mazda Carol.

Seventh generation (2009)

Japan

The seventh generation was first shown at the 2009 Tokyo Motor Show alongside its sister car, the Mazda Carol. It is available with a engine, a 5-speed manual, a 4-speed automatic transmission or a CVT, in FWD or 4WD variants. Under the Japanese 10-15 test cycle, the front-wheel-drive with CVT achieves 24.5 km/litre fuel economy.
In 2011, Suzuki launched the Alto Eco variant, that features the R06A engine lifted from the Suzuki MR Wagon and an idling stop function. It is capable of reaching 30.2 km/L based on Japan's JC08 Mode test cycle. This is.2 km/L higher than the Daihatsu Mira e:S.
In 2013, the Alto Eco was updated with the addition of Suzuki's ENE-CHARGE system, first applied on the fifth generation Wagon R. With this technology, fuel economy has now improved to 33.0 km/L based on Japan's JC08 Mode test cycle.

International

The Suzuki Alto available in international market is known in India as the Maruti Suzuki A-Star, but is also known as the Suzuki Celerio in some other countries. It was launched in December 2008 by Suzuki's Indian subsidiary Maruti Suzuki.
It is actually a different car from the Japanese market one although they share the same name. The car is manufactured exclusively in Haryana, India and is exported worldwide. It is available in some European markets with a somewhat different front end as the Nissan Pixo. The car was rolled out to the Indian customers in December 2008 and exports began in April 2009.
With a totally new body and engine, Maruti hopes to bring freshness to the Indian car market, of which it already holds a major share. The K10B inline-three engine was developed especially for the new car, and is also used for the Nissan Pixo. The A-Star has a fresh new dashboard, with an available unique protruding tachometer besides the usual meter cowl.
In February 2014, Maruti Suzuki unveiled an all-new Celerio, which replaces the A-Star and Zen Estilo.
The European market version of the Maruti Suzuki A-Star was unveiled at the 2008 Paris Motor Show. It was developed to be a global car and will be made at Maruti Suzuki's plant in Manesar, Haryana, India. It is stylistically based on the Suzuki A-Star Concept. The Alto was conceived as a response to high petrol prices and global warming. It was released as an eco-friendly car priced from £6,795 OTR.

Nissan Pixo

The Nissan Pixo is the "sister car" to the Suzuki Alto featuring a few notable differences, including the main grille and headlamps. It was launched at the 2008 Paris Motor Show and was available in Europe from 2009-2013. Because it was developed and built cheaply in India, the Pixo could be bought new for just under £7,000. In the summer of 2013, the Pixo was withdrawn from UK showrooms.

Eighth generation (2014)

The eighth generation Alto was introduced in Japan in December 2014 and has a more retro style. The new Alto was designed to have a very low fuel consumption, and is lighter than the outgoing model. This was achieved using "Suzuki Green Technology" for the body and the engine, and resulted in the car having a claimed fuel consumption of 37 km/L. The new Alto is available with either a naturally-aspirated inline-three engine, or a turbocharged version of the same power unit. It is available with either a 5-speed manual transmission, 5-speed semi-automatic transmission or a CVT. A Turbo RS variant started production in March 2015 which was followed by a performance-tuned Works edition by the end of the year.

Pakistan

The eight generation was revealed for the Pakistani market on 12 April 2019 at the Pakistan Auto Show. The car is sold in three variants: VX, VXR and VXL - VX being the base model with minimal equipment, no air conditioning and a 5-speed manual transmission; the VXR variant equipped with the standard manual transmission and with AC; while the premium VXL model is equipped with an automatic transmission. The base price of the car starts from US$6500 and goes up to US$8500, including the country's FED.
It is considered to be Pakistan's first locally manufactured 660 cc car. Currently, Pakistan is the only country, other than Japan, to locally manufacture this generation of Suzuki Alto. Pak Suzuki Motors' second generation Alto looks cosmetically the same as the Japanese-made one and is powered by the same engine.

In popular culture