Pneumatic cylinder


Pneumatic cylinder are mechanical devices which use the power of compressed gas to produce a force in a reciprocating linear motion.
Like hydraulic cylinders, something forces a piston to move in the desired direction. The piston is a disc or cylinder, and the piston rod transfers the force it develops to the object to be moved. Engineers sometimes prefer to use pneumatics because they are quieter, cleaner, and do not require large amounts of space for fluid storage.
Because the operating fluid is a gas, leakage from a pneumatic cylinder will not drip out and contaminate the surroundings, making pneumatics more desirable where cleanliness is a requirement. For example, in the mechanical puppets of the Disney Tiki Room, pneumatics are used to prevent fluid from dripping onto people below the puppets.

Operation

General

Once actuated, compressed air enters into the tube at one end of the piston and imparts force on the piston. Consequently, the piston becomes displaced.

Compressibility of gases

One major issue engineers come across working with pneumatic cylinders has to do with the compressibility of a gas. Many studies have been completed on how the precision of a pneumatic cylinder can be affected as the load acting on the cylinder tries to further compress the gas used. Under a vertical load, a case where the cylinder takes on the full load, the precision of the cylinder is affected the most. A study at the National Cheng Kung University in Taiwan, concluded that the accuracy is about ± 30 nm, which is still within a satisfactory range but shows that the compressibility of air has an effect on the system.

Fail safe mechanisms

s are often found in settings where even rare and brief system failure is unacceptable. In such situations, locks can sometimes serve as a safety mechanism in case of loss of air supply and, thus remedy or abate any damage arising in such a situation.
Leakage of air from the input or output reduces the output pressure.

Types

Although pneumatic cylinders will vary in appearance, size and function, they generally fall into one of the specific categories shown below. However, there are also numerous other types of pneumatic cylinder available, many of which are designed to fulfill specific and specialized functions.

Double-acting cylinders

Double-acting cylinders use the force of air to move in both extend and retract strokes. They have two ports to allow air in, one for outstroke and one for instroke. Stroke length for this design is not limited, however, the piston rod is more vulnerable to buckling and bending. Additional calculations should be performed as well.

Multi-stage, telescoping cylinder

Telescoping cylinders, also known as telescopic cylinders can be either single or double-acting. The telescoping cylinder incorporates a piston rod nested within a series of hollow stages of increasing diameter. Upon actuation, the piston rod and each succeeding stage "telescopes" out as a segmented piston. The main benefit of this design is the allowance for a notably longer stroke than would be achieved with a single-stage cylinder of the same collapsed length. One cited drawback to telescoping cylinders is the increased potential for piston flexion due to the segmented piston design. Consequently, telescoping cylinders are primarily utilized in applications where the piston bears minimal side loading.

Other types

Although SACs and DACs are the most common types of pneumatic cylinder, the following types are not particularly rare:
Rodless cylinders have no rod, only a relatively long piston. Cable cylinders retain openings at one or both ends, but pass a flexible cable rather than a rod. This cable has a smooth plastic jacket for sealing purposes. Of course, a single cable has to be kept in tension.. Other rodless cylinders close off both ends, coupling the piston either magnetically or mechanically to an actuator that runs along the outside of the cylinder. In the magnetic type, the cylinder is thin-walled and of a non-magnetic material, the cylinder is a powerful magnet, and pulls along a magnetic traveller on the outside.
In the mechanical type, part of the cylinder extends to the outside through a slot cut down the length of the cylinder. The slot is then sealed by flexible metal sealing bands on the inside and outside. The piston itself has two end seals, and between them, camming surfaces to "peel off" the seals ahead of the projecting linkage and to replace them behind. The interior of the piston, then, is at atmospheric pressure.
One well-known application of the mechanical type are the catapults used on many modern aircraft carriers.

Design

Construction

Depending on the job specification, there are multiple forms of body constructions available:
Upon job specification, the material may be chosen. Material range from nickel-plated brass to aluminum, and even steel and stainless steel. Depending on the level of loads, humidity, temperature, and stroke lengths specified, the appropriate material may be selected.

Mounts

Depending on the location of the application and machinability, there exist different kinds of mounts for attaching pneumatic cylinders:

Sizes

Air cylinders are available in a variety of sizes and can typically range from a small air cylinder, which might be used for picking up a small transistor or other electronic component, to diameter air cylinders which would impart enough force to lift a car. Some pneumatic cylinders reach in diameter, and are used in place of hydraulic cylinders for special circumstances where leaking hydraulic oil could impose an extreme hazard.

Pressure, radius, area and force relationships

Rod stresses

Due to the forces acting on the cylinder, the piston rod is the most stressed component and has to be designed to withstand high amounts of bending, tensile and compressive forces. Depending on how long the piston rod is, stresses can be calculated differently. If the rods length is less than 10 times the diameter, then it may be treated as a rigid body which has compressive or tensile forces acting on it. In which case the relationship is:
Where:
However, if the length of the rod exceeds the 10 times the value of the diameter, then the rod needs to be treated as a column and buckling needs to be calculated as well.

Instroke and outstroke

Although the diameter of the piston and the force exerted by a cylinder are related, they are not directly proportional to one another. Additionally, the typical mathematical relationship between the two assumes that the air supply does not become saturated. Due to the effective cross sectional area reduced by the area of the piston rod, the instroke force is less than the outstroke force when both are powered pneumatically and by same supply of compressed gas.
The relationship between the force, radius, and pressure can derived from simple distributed load equation:
Where:

Outstroke

Using the distributed load equation provided the can be replaced with area of the piston surface where the pressure is acting on.
Where:

Instroke

On instroke, the same relationship between force exerted, pressure and effective cross sectional area applies as discussed above for outstroke. However, since the cross sectional area is less than the piston area the relationship between force, pressure and radius is different. The calculation isn't more complicated though, since the effective cross sectional area is merely that of the piston surface minus the cross sectional area of the piston rod.
For instroke, therefore, the relationship between force exerted, pressure, radius of the piston, and radius of the piston rod, is as follows:
Where: