Hybrid Memory Cube is a high-performance RAM interface for through-silicon vias -based stacked DRAM memory competing with the incompatible rival interface High Bandwidth Memory.
Overview
Hybrid Memory Cube was co-developed by Samsung Electronics and Micron Technology in 2011, and announced by Micron in September 2011.. It promised a 15 times speed improvement over DDR3. The Hybrid Memory Cube Consortium is backed by several major technology companies including Samsung, Micron Technology, Open-Silicon, ARM, HP, Microsoft, Altera, and Xilinx. Micron, while continuing to support HMCC, is discontinuing the HMC product in 2018 when it failed to achieve market adoption. HMC combines through-silicon vias and microbumps to connect multiple dies of memory cell arrays on top of each other. The memory controller is integrated as a separate die. HMC uses standard DRAM cells but it has more data banks than classic DRAM memory of the same size. The HMC interface is incompatible with current DDRn and competing High Bandwidth Memory implementations. HMC technology won the Best New Technology award from The Linley Group in 2011. The first public specification, HMC 1.0, was published in April 2013. According to it, the HMC uses 16-lane or 8-lane full-duplex differential serial links, with each lane having 10, 12.5 or 15 Gbit/s SerDes. Each HMC package is named a cube, and they can be chained in a network of up to 8 cubes with cube-to-cube links and some cubes using their links as pass-through links. A typical cube package with 4 links has 896 BGA pins and a size of 31×31×3.8 millimeters. The typical raw bandwidth of a single 16-lane link with 10 Gbit/s signalling implies a total bandwidth of all 16 lanes of 40 GB/s ; cubes with 4 and 8 links are planned, though the HMC 1.0 spec limits link speed to 10 Gbit/s in the 8-link case. Therefore, a 4-link cube can reach 240 GB/s memory bandwidth, while an 8-link cube can reach 320 GB/s bandwidth. Effective memory bandwidth utilization varies from 33% to 50% for smallest packets of 32 bytes; and from 45% to 85% for 128 byte packets. As reported at the HotChips 23 conference in 2011, the first generation of HMC demonstration cubes with four 50 nm DRAM memory dies and one 90 nm logic die with total capacity of 512 MB and size 27×27 mm had power consumption of 11 W and was powered with 1.2 V. Engineering samples of second generation HMC memory chips were shipped in September 2013 by Micron. Samples of 2 GB HMC are packed in a 31×31 mm package and have 4 HMC links. Other samples from 2013 have only two HMC links and a smaller package: 16×19.5 mm. The second version of the HMC specification was published on 18 November 2014 by HMCC. HMC2 offers a variety of SerDes rates ranging from 12.5 Gbit/s to 30 Gbit/s, yielding an aggregate link bandwidth of 480 GB/s, though promising only a total DRAM bandwidth of 320 GB/sec. A package may have either 2 or 4 links, and a quarter-width option is added using 4 lanes. The first processor to use HMCs was the FujitsuSPARC64 XIfx, which is used in the Fujitsu PRIMEHPC FX100 supercomputer introduced in 2015. JEDEC's Wide I/O and Wide I/O 2 are seen as the mobile computing counterparts to the desktop/server-oriented HMC in that both involve 3D die stacks. In August 2018, Micron announced a move away from HMC to pursue competing high-performance memory technologies such as GDDR6 and HBM.https://www.micron.com/about/blog/2018/august/micron-announces-shift-in-high-performance-memory-roadmap-strategy
