In dentistry, a furcation defect is bone loss, usually a result of periodontal disease, affecting the base of the root trunk of a tooth where two or more roots meet. The extent and configuration of the defect are factors in both diagnosis and treatment planning. A tooth with a furcation defect typically possessed a more diminished prognosis owing to the difficulty of rendering the furcation area free from periodontal pathogens. For this reason, surgical periodontal treatment may be considered to either close the furcation defect with grafting procedures or allow greater access to the furcation defect for improved oral hygiene.
Root trunk length
The distance between the cementoenamel junction and the furcation entrance is called the root trunk length. This distance plays an important role in furcation defects because the deeper the furcation entrance is within the bone, the more bone loss necessary before the furcation becomes exposed. For mandibular first molars, the mean root trunk length is 3 mm on the buccal aspect and 4 mm on the lingual aspect. The root trunk lengths for mandibular second and third molars are either the same or slightly greater than for first molars, although the roots may be fused. For maxillary first molars, the mean root trunk length is 3-4 mm on the buccal aspect, and 4-5 mm on the mesial aspect and 5-6 mm on the distal aspect. As with mandibular molars, the root trunk lengths for maxillary second and third molars are either the same or slightly greater than for first molars, although the roots may be fused. For maxillary first premolars, there is a bifurcation 40% of the time and the mean root trunk length is 8 mm from both mesial and distal.
Furcation defect classification
Because of its importance in the assessment of periodontal disease, a number of methods of classification have evolved to measure and record the severity of furcation involvement; most of the indices are based on horizontal measurements of attachment loss in the furcation. In 1953, Irving Glickman graded furcation involvement into the following four classes:
Grade II - There is a definite horizontal component to the bone loss between roots resulting in a probeable area, but sufficient bone still remains attached to the tooth so that multiple areas of furcal bone loss, if present, do not communicate.
Grade III - Bone is no longer attached to the furcation of the tooth, essentially resulting in a through-and-through tunnel. Because of an angle in this tunnel, however, the furcation may not be able to be probed in its entirety; if cumulative measurements from different sides equal or exceed the width of the tooth, however, a grade III defect may be assumed. In early grade III lesions, soft tissue may still occlude the furcation involvement, thus, making it difficult to detect.
Grade IV - Essentially a super grade III lesion, grade IV describes a through-and-through lesion that has sustained enough bone loss to make it completely probeable.
In 2000, Fedi, et al. modified Glickman's classification to include two degrees of a grade II furcation defect:
Grade II degree I - exists when furcal bone loss possesses a vertical component of >1 but <3mm.
Grade II degree II - exists when furcal bone loss possesses a vertical component of >3mm, but still does not communicate through-and-through.
In 1975, Sven-Erik Hamp, together with Lindhe and Sture Nyman, classified furcation defects by their probeable depth.
Class I - Furcation defect is less than 3 mm in depth.
Class II - Furcation defect is at least 3 mm in depth but not through-and-through (i.e. there is still some interradicular bone attached to the angle of the furcation. The furcation defect is thus a cul-de-sac.
Class III - Furcation defect encompassing the entire width of the tooth so that no bone is attached to the angle of the furcation.
Diagnosis
Nabers probe is used to check for furcation involvement clinically. Recently, cone beam computerised technology has also be used to detect furcation. Periapical and interproximal intraoral radiographs can help diagnosing and locating the furcation. The location and severity of furcation should be recorded in patient’s notes. Only multirooted teeth have furcation. Therefore, upper first premolar, maxillary and mandibular molars may be involved. Upper premolars have one buccal and one palatal root. Furcation involvement should be checked from the mesial and the distal aspects of the tooth. Maxillary molars have three roots, a mesio-buccal root, disto-buccal root and a palatal root. Thus, check for furcation from buccal, mesio-palatal and disto-palatal aspects. Mandibular molars have one mesial and one distal root, and so, check for involvement from buccal and lingual aspects.
Treatment
The treatment aims are to eliminate the bacteria from the exposed surface of the root and to establish the anatomy of the tooth, so that better plaque control can be achieved. Treatment plans for patients differ depending on the local and anatomical factors. For Grade I furcation, scaling and polishing, root surface debridement or furcationplasty could be done if suitable. For Grade II furcation, furcationplasty, open debridement, tunnel preparation, root resection, extraction, guided tissue regeneration or enamel matrix derivative could be considered. As for Grade III furcation, open debridement, tunnel preparation, root resection, GTR, or tooth extraction could be performed if appropriate. Tooth extraction is usually considered if there is extensive loss of attachment or if other treatments will not obtain good result.
