Ford flathead V8 engine
The Ford flathead V8 is a V8 engine of the valve-in-block type designed by the Ford Motor Company and built by Ford and various licensees. During the engine's first decade of production, when overhead-valve engines were used by only a small minority of makes, it was usually known simply as the Ford V‑8, and the first car model in which it was installed, the Model 18, was often called simply the "Ford V‑8", after its new engine. Although the V8 configuration was not new when the Ford V8 was introduced in 1932, the latter was a market first in the respect that it made an 8-cylinder affordable and a V engine affordable to the emerging mass market consumer for the first time. It was the first independently designed and built V8 engine produced by Ford for mass production, and it ranks as one of the company's most important developments. A fascination with ever-more-powerful engines was perhaps the most salient aspect of the American car and truck market for a half century, from 1923 until 1973. The engine was intended to be used for big passenger cars and trucks; it was installed in such until 1953, making the engine's 21-year production run for the U.S. consumer market longer than the 19-year run of the Ford Model T engine for that market. The engine was on Ward's list of the 10 best engines of the 20th century. It was a staple of hot rodders in the 1950s, and it remains famous in the classic car hobbies even today, despite the huge variety of other popular V8s that followed.
Development and production overview
Before this engine's introduction, almost all mass-produced cars affordable to the "average mass-market consumer" used inline-four and inline-six cylinder engines. Since French engineer Léon Levavasseur's invention of the V8 engine in 1902, multi-cylinder V-engines were produced, but were used in luxury models and their production runs were thus limited. For example, the first Cadillac V8 engine was in that category.Even though Ford had an engineering team assigned to develop the engine, many of the ideas and innovations were Henry Ford's. The Model A, its variants, and this V8 engine were developed between 1926 and 1932, and this period was the elder Ford's last central contribution to the company's engineering.
Mercury's version was introduced in 1939. Aftermarket heads were available from Barney Navarro, Vic Edelbrock, and Offenhauser.
An economizing design feature of this engine was the use of three main bearings to support the crankshaft, rather than the customary five bearings used with most V-8s. The flathead mounted the camshaft above the crankshaft, like later pushrod-operated overhead-valve engines. Valves for each bank were mounted inside the triangular area formed by the "vee" of cylinders. The intake manifold fed both banks from inside the vee, but the exhaust ports had to pass between the cylinders to reach the outboard exhaust manifolds. Such an arrangement transferred exhaust heat to the block, imposing a large cooling load; it required far more coolant and radiator capacity than equivalent overhead-valve V8 engines. Ford flathead V8s were notorious for cracking blocks if their barely adequate cooling systems were overtaxed. The simple design left much room for improvement, and the power available after even low cost modifications was usually substantially more than could be obtained from an overhead-valve inline six-cylinder engine of similar displacement.
The Ford flathead V8 was licensed to other producers. It was used by Simca in France until 1961 and in Brazil until 1964 for cars and until 1990 in the Simca Unic Marmon Bocquet military truck. In the United States, the flathead V8 was replaced by the more modern overhead-valve Ford Y-block engine in 1954.
Components
Crankshaft
The crankshaft development for the Ford flathead V8 was pioneering. The engine's production development program began with a forged steel crank, per conventional practice, but Ford then developed the improved foundry practice, heat-treating, and materials handling logistics to make the cranks from cast steel instead, yielding in the end a crank just as strong, but less expensive to produce. These new methods were patented. The simple three-main-bearing crankshaft attached two connecting rods to a single crankpin, one rod from each cylinder bank. As with other crankshafts, static and dynamic balancing was performed.The short crankshaft proved quite durable in comparison to six-cylinder engines when roughly handled. For these reasons, the flathead Ford became a favorite among hot-rodders, and this in turn led to a rich supply of aftermarket performance parts. With the use of specialized pistons or connecting rods the stroke of the crankshaft could be increased by welding and regrinding as a method of increasing engine displacement, usually in combination with overboring as described below.
The sought-after crankshaft by hot rodders is the stroke Mercury version. It can be identified by the four diameter clean-out plugs, two in the front of the front rod throws and two in the back of the back two rod throws of the crankshaft. They measure on the Mercury crankshaft and on the Ford crankshaft, usually. The French military cranks, at least sometimes, had the plugs in the stroke cranks. The crankshafts came in the 1949 to 1953 engines.
Block
One of the most important innovations in the Ford flathead V8 was the casting of the crankcase and all 8 cylinders in one engine block. This level of monobloc design for V-8 blocks had been accomplished before, but it had never seen mass production. Making it practical for the latter was an example of the production development needed to bring a V8 engine to the widely affordable segment of the market. Most V engines of the time had multiple cylinder blocks bolted to a common crankcase. At most, each bank of the V was an integral block, but many V engines had 4- or even 6-cylinder blocks, with cylinders cast in pairs or triples. Like most other engine blocks then and now, it was cast iron; but the foundry practice was a revolutionary advancement in the mass production of castings. Charles E. Sorensen lived up to his longtime nickname at Ford, "Cast-Iron Charlie", by leading this revolution to bring Ford's first V8 to market.As with any V8, the block was relatively light for the displacement supported. The cooling jacket reaches down to the bottom dead centre, which is unusually low. American engineers at the time believed this would improve the piston cooling. The bottom of the block formed the parting line for the main bearing caps. The most complex part of the block was the exhaust passage routing. The exhaust valves were on the inside of the V and exhaust flow was initially downward and passed around the cylinders through the water jacket to exit on the outside of the cylinder block. The routing of the exhaust through the water jacket put an extremely heavy load on the cooling system and led to frequent overheating, especially on early models, if the cooling system was not maintained. Somewhat primitive water pumps used until the advent of the 1948 8RT and 1949 8BA models also contributed to the overheating problem. The space for the exhaust flow was also somewhat restricted, so the exhaust passages were tall and narrow in some locations. The gas flow past the rough sand castings could be greatly improved by polishing the passages. The capacity of the block for over-boring was limited by the configuration and the metal available. In early blocks, some cylinder walls were extremely thin due to cores shifting during casting. It was prudent to overbore before relieving and polishing the ports, as a casting flaw such as a sand pit might be revealed, usually fatal to further use of the block. The blocks with the factory bore can usually be safely bored over standard to and sometimes can be bored over standard to, increasing displacement a little over 12%.
Bearings
The engines built from 1932 to 1935 had poured main bearings which required skill and machine shop equipment to overhaul. Part of the 1936 production and all production from 1937 to the end of flathead V8 production had both replaceable shell main bearings and connecting rod inserts, enabling straightforward and low cost rebuilding, another reason why the Ford was a favorite of amateur mechanics. These shell main bearings are made of a cadmium silver alloy.Camshaft and timing
The Ford flathead V8 has a single camshaft located inside the engine block above the crankshaft. It is spur gear driven; the camshaft's spur gear is made of plastic. The camshaft has three camshaft bearings. A lid made of cast iron covers the camshaft spur gears; the ignition distributor is placed on top of this lid and is driven by the camshaft spur gears. For powering the fuel pump, the camshaft is fitted with an extra cam located in the bearing on the flywheel side.Lubrication
Also unlike the Chevrolet inline 6, Ford products used high oil pressure for lubrication for the main and rod bearings, as do all modern vehicle combustion engines. This offered a significant performance advantage, as full pressure lubrication allowed for continuous use above 3500 rpm and not starve the rod bearings for oil, which was necessary for high performance applications, such as racing. For this reason, bank robber Clyde Barrow preferred to steal Fords as getaway vehicles. It also eliminated a complex oil jet system to feed the rod bearings in the oil pan. As a side benefit to a prospective purchaser of a used vehicle, this also enabled the condition of the connecting rod and main bearings to be determined indirectly by observation of the analog oil pressure gauge after the vehicle was warmed up, provided that oil of normal viscosity was in use.Exhaust
The exhaust outlets in the 1932-48 cars and the 1932-47 trucks were near the front of the manifolds aiming down and sometimes out. A Y-pipe took the exhaust gases to the right side of the vehicle to a single muffler, then to a single pipe out the back on the right side. The left side exhaust manifold exhausted to the front in the 1949–53 Ford cars, where a crossover pipe took the exhaust to the forward end of the right side manifold on the car engines and between the 1st and second cylinder on some trucks, in turn exhausting to a single pipe at the rear.A common conversion for the 1949-53 Ford cars and 1952-53 Mercurys was to block off the right forward manifold entrance and route the left side exhaust to a new pipe to form a dual exhaust system with better flow characteristics. These typically involved installation of free-flowing mufflers, which if at a legal noise level still allowed low frequency sounds to pass, giving a characteristic rumbling dual exhaust sound to these systems. In the 1950s shortcut exhaust outlets with manually removed covers were added to street machines in emulation of vehicles intended for high speed straight line racing on dry lake beds, typically located just behind the front wheel, although chromed external runners sometimes extended to just forward of the rear wheel. These covers were referred to as lake plugs, the pipes as lake pipes. This style exhaust was also used legally in sanctioned drag racing and illegally in unsanctioned performance demonstrations.
Internal Air flow
More extreme modifications were to improve the airflow by removing material from the top of the block between the valves and the cylinders, increasing the size of the inlet and exhaust passages, and by polishing the sand-cast surfaces to improve air flow. Increased compression ratios could be cheaply obtained by milling material from the head or by obtaining aluminum heads as aftermarket parts. Higher capacity intake manifolds were similarly available. Changing the camshaft to a higher performance version required head removal so that the valves could be held up out of the way, so this was usually done only as part of a substantial rework of the basic engine.Overhead-valve kits
A popular modification for the flathead was conversion to an overhead-valve configuration, and many such modification kits were available, including the Ardun heads from Zora Arkus-Duntov who was to go on to fame as the "father of the Corvette". These conversions were not initially demanded by hot rodders looking for extra power, as they had not yet exhausted the capabilities of the flathead configuration, but were demanded by users of the engine in trucks and other such high load applications, where the constant flow of hot exhaust through the block to the exhaust manifolds caused the entire engine to overheat; the overhead-valve heads routed the exhaust out more directly, and away from the block.Hot-rodding applications
In the early 1950s, many hot-rodders could not afford to purchase and modify even a "cheap" flathead V-8, and a large investment in machine work and aftermarket parts was necessary to bring a Ford flathead V-8 to even the performance levels of most stock OHV V-8s available at the time. Even many inline six-cylinder engines from that period could be modified to produce more reliable and practical power than Ford V-8s, as the Ford flathead V-8 is saddled with many design features that make modifying it for true high-performance use difficult and expensive compared with other V-8s.As modern OHV V-8s became available and affordable in salvage yards, the Ford flathead V-8 rapidly disappeared from the hot-rodding scene. Hot-rodding in general moved away from the salvage-yard car builds as parts and labor became more expensive and many hot-rod shops priced themselves out of business. The modern OHV V-8 powered vehicles available also contributed to the demise of hot-rodding's original culture, as new factory cars became capable of much higher performance than most hot-rods.
Today the flat-head Ford is mainly used in "retro" hot-rod builds by builders more interested in a retro vibe and recreating history than performance. Even 4-cylinder Ford engines are used to make a retro hot-rod "correct".
Modern performance flatheads
Ford flatheads are still hot rodded today, with a special land speed record class for flathead engines. The current record holder achieves and. On one pass the car broke but did not set a record. Two passes have to be made in order to break the record.Tractor conversions
During the 1930s to 1950s, the farm market in North America and parts of Europe demanded ever-increasing power output from farm tractors. It was in this climate that Ford experimented with V-8 tractor designs, some individual farmers converted their 4-cylinder tractors to Ford inline-6 or V-8 engines, and a few aftermarket companies offered such conversions for sale. Among the latter, the best-known were Funk conversions by brothers Joe and Howard Funk. In the 1930s, the Funk brothers built aircraft—including the Funk B, which used an engine design based on Ford engines. In the late 1940s, their aircraft line became unprofitable, but they found renewed profitability in aftermarket parts for tractors—transmissions, engines, and accessories. They sold many converted Ford N-Series tractors and conversion kits using Ford industrial inline-6 engines and Ford flathead V-8 engines.Version types
Types are classified by their displacement.221
The original flathead engine displaced, with bore and stroke.Street Rodder, 1/85, p. 73 The block was cast as a single piece for durability, and a single-barrel carburetor fed the engine. The 1932 V8-18 with 5.5:1 compression produced. The 1933-34 V8-40 raised compression to 6.33:1 and power to. In 1934 a two barrel down draft carburetor was introduced. 1935's V8-48 saw compression drop to 6.3:1, but power climb to, and torque was rated at. It became the V8-68 in 1936, with compression, horsepower, and torque unchanged.Production of the original 221 lasted from 1932 through to 1936. These engines can be identified by having the water pumps located at the front of the heads. A similar 221 flathead was used in Fords for 1937 and 1938 but the block was revised to have the water pumps mounted on the block. The new design also relocated the water outlet from the front of the heads to the top center of the heads. These, designated V8-78, were offered with standard 6.2:1 compression aluminum or 7.5:1 compression iron cylinder heads, rated at and or . The 1932 through 1938 motors used twenty one studs to hold down each head and are known as "21 stud" motors. This motor continued to be made into the 1950s in Europe.
In late 1938 Ford introduced V8-81A, commonly called the "24 stud" engine because it uses twenty four studs to hold down each head. This engine debuted at the same time as the 239 motor. With 6.12:1 compression, horsepower remained the same, but torque increased by. In 1939, as the V8-91A, compression increased to 6.15:1, power rose to, and torque reached ; the ratings remained the same for the 1940 V8-01A, 1941 V8-11A, and the last civilian model, the V8-21A, which saw compression rise, to 6.2:1. This engine was used through 1942 for civilian use and saw some use in military vehicles during World War Two. Collectively all 221 motors are commonly referred to as "85 horse" motors.
239
Ford introduced the V8-99A engine with bore and stroke and 6.15:1 compression in 1939. It produced and. This was done to provide a more powerful engine for the Mercury cars, which Ford Motor Company started making in 1939. It was used in Mercurys in 1939 and in Fords in 1946. This engine is very similar to the late 221 engine. As the V8-09A in 1940, compression, power, and torque were unchanged; in 1941, the V8-19A compression and power were static, but torque rose by, while the 1942 V8-29A increased compression to 6.4:1 and power to, while torque stayed the same. Postwar, it became the V8-69, with compression 6.75:1,, and. For 1947 and 1948, only the designation changed, to V8-79 and -89. The 239 was redesigned in 1948 as the 8RT for Ford trucks and in 1949 as the 8BA for the cars. It had higher 6.8:1 compression, but performance was unchanged. The 1950 V8-0BA boosted torque by, the 1951 -1BA by more, while in 1952, as the V8-B2, compression climbed to 7.2:1, power to, and torque to, then to in the -B3 of 1953, its final year. The 1948 to 1953 engines have a revised cooling and ignition system. Collectively all 239 engines are referred to as "100 horse" engines, although the horsepower was increased in 1952 to 110 horsepower in cars and 106 horsepower in trucks. This engine was used in Ford's transit buses during the most productive years of the company's short stint in the transit bus business from the mid-1930s to the early 1950s, most notably in the 1939-1947 version of the Ford Transit Bus.The latest iteration of this engine was used from 1948 to 1953 in the U.S and till 1954 in Canada. It was initially designated the 8BA in automobiles and the 8RT in trucks. 8RT remained the truck engine designation throughout the entire run from 1948 through 1953 in the U.S. The engines were essentially identical. Earlier Ford V8s had the unique Ford designed distributor driven directly from the forward end of the camshaft, which was an inconvenient location for maintenance. This final flathead used a more conventional distributor driven at a right angle to the crankshaft and located at the right front of the engine where it was readily accessible. The water inlets and thermostat housings were moved to the front end of the heads, and the 24 studs and nuts that attached the heads on the old engine were replaced by 24 bolts.
136
A V8-74 version was introduced in the United States in 1937. With bore and stroke and 6.6:1 compression, the engine was rated and. The designation changed again in 1939, to V8-922A, but the specifications remained the same. It was produced in Europe in 1935 and 1936, and was used in the many standard Ford vehicles based on the car platform of the era. It was not very popular with U.S. buyers who were used to the cars. Redesignated V8-82A in 1938, V8-922A in 1939, and V8-022A in 1940, compression, power, and torque remained unchanged. The engine was very popular as a powerplant for midget race cars after World War II. This engine is most commonly referred to as the "60 horse" flathead, or the V8-60. It was replaced by the 226 straight-6 in the 1941 Fords, though it would continue to be used after the war in the French Ford Vedette and the British Ford Pilot.In 1952 Ford France created a somewhat bored out version displacing. Production was taken over by Simca in 1954 who began installing it in their Simca Vedette in 1955. Simca then transferred the Aquilon production line to Simca do Brasil, where it was kept in production until 1969. Simca do Brasil introduced a version in May 1962 but the real surprise was the "Emi-Sul" of April 1966. This engine has overhead valves and hemispherical combustion chambers; it produced in its most powerful version.
255
The 1948-1953, referred to as the model BG, was achieved by use of a stroke crankshaft in the 8BA/8RT engine. It was only used in Mercury cars, and heavy service trucks. Known as the V8-9CM in 1949, it featured 6.8:1 compression,, and torque, which stayed the same for the 1950 V8-0CM. The 1951 V8-1CM raised this by, and torque, The 1952 V8-MA boosted compression to 7.2:1, power to, and torque to, while only the name changed, dropping the -MA, for the last year of production, 1953.Because of interchangeability, the Mercury crank made a popular upgrade in the 239 among hot rodders. In fact, in the 1950s, the flathead block was often fitted with crankshafts of up to stroke.Street Rodder, 1/85, p. 72. In addition, rodders in the 1950s routinely bored them out by .
French-built 255 engines were fitted to the light trucks of the French military. When these were decommissioned around 1990, they provided a new source of little-worn engines for the hotrodding community. The block metallurgy, being much later, was also stronger than the originals.
337
The largest displacement version of the production Ford flathead V8 engine was designed for large truck service. When Lincoln could not produce the V12 engine it wanted for the 1949 model year, the 337 engine was adapted for passenger car use. The 337 features a bore and a stroke.It was introduced in the 1948 two and a half ton and three ton Ford trucks and the 1949 Lincoln passenger cars. It was produced through the 1951 model year. In 1952 it was replaced in the Lincoln passenger cars and Ford three ton trucks with the Lincoln Y-block overhead-valve V8. The two and a half ton Ford trucks got a version of the 317 engine.
In the song "Hot Rod Lincoln", the engine referred to in the original lyrics was a Lincoln V12 not mentioned in the Commander Cody version.